CO Guardian CO Detector

MVP-50 Display

Weight:1.9 Lbs. Environmental: TSO'd to DO-160 Software: TSOd to DO-178B Power Requirements: 7.5 to 30 Volts, .3 Amps @24V (Typical), .6 Amps @ 12V (Typical). USB Port: For USB Memory Sticks Only (not intended to provide power to other electronic devices) Display: Active TFT Matrix, 262,144 colors. Sunlight readable. Backlight: External Control Line and Internal Electric Eyes

EDC-33P-4/6

Weight: 1 Lbs. Environmental: Meets TSO (DO-160) Software: Designed and documented to TSO (DO-178B) Power Requirements: 7.5 Volts to 30 Volts, 0.1 amps (Typical).

Inputs

Volts: Measured on the power lead of the EDC. Amps: +/- 2.5V differential input, +/- 90V common mode operating range Fuel Flow: 2.5V trigger, 5.11K Ohm pull-up to +5V, 0 to 8.3KHz. RPM: 2 ea. inputs, may be configured for digital or mag input. Selectable jumper for 4 or 6 Cylinder operation. Over voltage protection for RPM: 3V trigger, impendence = 2.06K with 1V pickup. Pressure: 6 ea. inputs, 0 to 2.5V differential input. Impendence >20M Ohms, common mode = 0 to 4 Volts. Temperature: 17 ea. inputs, 0 to 2.5V differential input. Impendence = 12.1K Ohms, common mode = 0 to 4V. Resistive Fuel Level: 4 ea. inputs, 0 to 18V single ended input, impendence = 14.4K Ohms Capacitive Fuel Level: 4 ea. inputs, 0 to 6 KHz. 2.1V trigger, impendence = 33.2K Ohms

• Dimensions: 4.53 x 3.32, 0.5 deep
• Pre-Wired Harness for all functions
• Display SVGA
• RPM Prop
• MAP Manifold Pressure
• % HP Percent of Horse Power
• EGT Exhaust Gas Temp.
• CHT Cylinder Head Temp.
• EGT Normalize mode
• LOP/ROP JPI Exclusive Leaning Mode
• O-T Oil Temperature
• O-P Oil Pressure
• F-P Fuel Pressure (when in POH)
• OAT Outside Air Temp.
• VDC Voltage (1)
• AMP Current amps (2 twins)
• Fuel Flow Transducer FlowScan
• GPH Gallons per Hour GPH
• REQ Required to wp or destination
• USD Fuel used
• H:M Endurance Hours and Minutes
• MPG Miles per Gal
• CLD Shock Cooling on ALL cylinders
• DIFF Difference between EGT’s
• USB Memory stick 1 GB
• Data Recording 800 Hrs every 6 sec.
• EZTrends Graphing Software free
• 3 year Warranty

Accuracy and Resolution, are two of the most misunderstood terms in instrumentation. Because an instrument displays 1 degree increments (resolution) does not mean it is accurate to 1 degree. JPI’s accuracy comes from its linearized thermocouples. Other’ put and estimating straight line through the center of the thermocouple calibration “S” curve. With this method the instrument is accurate at only three points along as the the straight line crosses the “S” curve. Therefore errors of +/- 10' are quite possible while still displaying in 1degree resolution. Our competition is advertising +/- 1/2' accuracy at full scale. This would mean that =/-1/2' of 2000' (full scale) is +/- 10'; there is a big difference. JPI has found nothing in the Aviation market that compares to our linearized accuracy.

• Dimensions: 5.97 x 5.11, 2.99 deep
• Pre-Wired Harness for all functions
• Display SVGA
• RPM Prop
• MAP Manifold Pressure
• % HP Percent of Horse Power
• EGT Exhaust Gas Temp.
• CHT Cylinder Head Temp.
• EGT Normalize mode
• LOP/ROP JPI Exclusive Leaning Mode
• O-T Oil Temperature
• O-P Oil Pressure
• F-P Fuel Pressure (when in POH)
• OAT Outside Air Temp.
• VDC Voltage (1)
• AMP Current amps (2 twins)
• Fuel Flow Transducer FlowScan
• GPH Gallons per Hour GPH
• REQ Required to wp or destination
• USD Fuel used
• H:M Endurance Hours and Minutes
• MPG Miles per Gal
• CLD Shock Cooling on ALL cylinders
• DIFF Difference between EGTs
• USB Memory stick 1 GB
• Data Recording 800 Hrs every 6 sec.
• EZTrends Graphing Software free
• 3 year Warranty

The EDM 930 is a self contained instrument. All functions or channels on the EDM are recorded at an adjustable rate of every 2 to 60 seconds per recording. The EDM-930 is sold in several versions.The display is a TFT, full VGA not 1/4 VGA display. This type of display permits a lot of latitude in placing the gages on the screen. The EDM-930 is sold in several versions.

• EDM-930 ALL IN ONE Bright VGA Display
• Pre-Wired Harness for all functions
• All EGT/ CHT probes
• Oil Pressure Transducer
• Oil Temperature Sensor
• Fuel Pressure Transducer
• Oat Sensor
• RPM Sensor, One required
• Manifold Pressure Transducer
• 100 amp Shunt (2)(for Amps)
• Volts pick-up V-1 and V-2
• 2 GB memory Download/upload stick
• FloScan Fuel Flow Transducer w/firesleeve
• Demo DVD
• 3 year Warranty

• Pre-Wired Harness for all functions
• Display SVGA
• RPM Prop
• MAP Manifold Pressure
• % HP Percent of Horse Power
• EGT Exhaust Gas Temp.
• CHT Cylinder Head Temp.
• EGT Normalize mode
• LOP/ROP JPI Exclusive Leaning Mode
• O-T Oil Temperature
• O-P Oil Pressure
• F-P Fuel Pressure (when in POH)
• OAT Outside Air Temp.
• VDC Voltage (1)
• AMP Current amps (2 twins)
• Fuel Flow Transducer FlowScan
• GPH Gallons per Hour GPH
• REQ Required to wp or destination
• USD Fuel used
• H:M Endurance Hours and Minutes
• MPG Miles per Gal
• CLD Shock Cooling on ALL cylinders
• DIFF Difference between EGT’s
• USB Memory stick 1 GB
• Data Recording 800 Hrs every 6 sec.
• EZTrends Graphing Software free
• 3 year Warranty

The EDM 960 is a self contained instrument. All functions or channels on the EDM are recorded at an adjustable rate of every 2 to 60 seconds per recording. The EDM-930 is sold in several versions.The display is a TFT, full VGA not 1/4 VGA display. This type of display permits a lot of latitude in placing the gages on the screen. The EDM-930 is sold in several versions.

• EDM-960 ALL IN ONE Bright VGA Display
• Pre-Wired Harness for all functions
• All EGT/ CHT probes
• Oil Pressure Transducer
• Oil Temperature Sensor
• Fuel Pressure Transducer
• Oat Sensor
• RPM Sensor, One required
• Manifold Pressure Transducer
• 100 amp Shunt (2)(for Amps)
• Volts pick-up V-1 and V-2
• 2 GB memory Download/upload stick
• FloScan Fuel Flow Transducer w/firesleeve
• Demo DVD
• 3 year Warranty