FS-450 Fuel Flow, Gravity flow (No fuel Pump)
$519.00
Description
Fuel Scan FS-450 All gravity Flow installations without fuel pump
With GPS interface, FlowScan Transducer and Fire sleeve
Purchase fittings separately to fit your engine.
- Continuous display of fuel burned,in upper display in Gallons per Hour. Liters and Lbs per hr also available.
- An amazingly low price includes Instrument harness and a Flow Scan 201 or 231 transducer.
- When your EI, Hoskins or Shadin fails, upgrade it to the FS-450 using the already installed transducer.
- Will function with any K factors with excellent accuracy; connector is pin to pin compatible.
- Automatically calculates the K factor.
- All programming done from the front panel.
- Dimensions: 2 1/4″ instrument round x 1.5″ deep
- Weight: Display 5.0 oz. Transducer 3.0 oz.
- 3 year factory warranty
- Serial port sends and receives data from all GPS units, even handhelds.
- Calculates fuel to next waypoint.
- FS-450 Can Mate to an old Shadin or Hoskins System
- Gallons per hour can be changed tap litres or Lbs.
- QUE lights indicate which function is being displayed in the lower display
- Auto Button, starts the automatic scan of the functions. Rate can be set from 1-9
- Continuous display of fuel burn in Gal/Lbs/Litres per hour.
- Step button can index information forward or backward. All programing done easily from the from panel with two buttons and no switches to toggle.
- Dual Displays show fuel-flow, GPH at all times.
- Large bright digits for excellent viewing in direct sunlight
- FAA TSO’d for reliability and accuracy
- Displays gallons required to next waypoint or destination.
- Programmable to display US gallons, pounds or liters
- Remote “Warning Light” programmable with low fuel and low time warning.
- Automatic reminder (flashing digits) to update fuel added. Fuel added can be set after take-off.
- Total fuel used can be set to zero at any time during flight.
- Return line systems (Pressure Carburetor) and gravity flow, no problem.
- Display passed TSO-C44b with operational temperature range -67ºF to 180ºF. Also TSO’d for use in Turbo-prop aircraft.
Displays All These Functions:
- Total Fuel Used
- Fuel Remaining
- Endurance in Hours and Minutes
- Fuel Required to next Waypoint
- Fuel Reserve at Next Waypoint
- Nautical miles per Gallon
[wpcc-iframe width=”420″ height=”315″ src=”https://www.youtube.com/embed/FOLXKNBXIcY” frameborder=”0″ allowfullscreen=””]
Related products
CGR-30P (2 Monitors) & CGR-30C Primary 4-Cylinder Twin Engine Monitor Combo
$7,919.00
- Models: CGR-30P
- FAA Certifications: STC’d, PMA’d and TSO’d
- Weight: 1.1 Lbs
- Environmental: Designed and Tested to TSO (DO-160G)
- Software: Designed and Documented to TSO (DO-178B, Level C)
- Minimum Performance Standards: TSO-C43c, TSO-C44c, TSO-C45b, TSO-C47a, TSO-C48a, TSO-49b and TSO-C55a
- Power Requirements: 7.5 to 30 Volts, 0.1 amps @ 24V (Typ), 0.2 amps @ 12 Volts (Typ)
- USB Port: For USB Memory Stick use only
- Display: Active Matrix TFT, 262,144 colors, Sunlight readable
- Backlight: External control line, programmable levels
- Display of Primary Gauges with Red and/or Yellow Ranges: Five on the Main Screen + EGT and CHT, One on the Secondary Screen
- Display of Primary and Non-Primary Gauges without Red and/or Yellow Ranges: Five on the Main Screen + EGT and CHT, Six on the Secondary Screen
CGR-30P 4-Cylinder Primary Twin Engine Monitors, Premium (2 Monitors) w/RPM, EGT/CHT & 10 Functions
$7,039.00
- Models: CGR-30P
- FAA Certifications: STC’d, PMA’d and TSO’d
- Weight: 1.1 Lbs
- Environmental: Designed and Tested to TSO (DO-160G)
- Software: Designed and Documented to TSO (DO-178B, Level C)
- Minimum Performance Standards: TSO-C43c, TSO-C44c, TSO-C45b, TSO-C47a, TSO-C48a, TSO-49b and TSO-C55a
- Power Requirements: 7.5 to 30 Volts, 0.1 amps @ 24V (Typ), 0.2 amps @ 12 Volts (Typ)
- USB Port: For USB Memory Stick use only
- Display: Active Matrix TFT, 262,144 colors, Sunlight readable
- Backlight: External control line, programmable levels
- Display of Primary Gauges with Red and/or Yellow Ranges: Five on the Main Screen + EGT and CHT, One on the Secondary Screen
- Display of Primary and Non-Primary Gauges without Red and/or Yellow Ranges: Five on the Main Screen + EGT and CHT, Six on the Secondary Screen
CGR-30P 6-Cylinder Primary Twin Engine Monitors, Premium (2 Monitors) w/RPM, EGT/CHT & 10 Functions
$7,919.00
- Models: CGR-30P
- FAA Certifications: STC’d, PMA’d and TSO’d
- Weight: 1.1 Lbs
- Environmental: Designed and Tested to TSO (DO-160G)
- Software: Designed and Documented to TSO (DO-178B, Level C)
- Minimum Performance Standards: TSO-C43c, TSO-C44c, TSO-C45b, TSO-C47a, TSO-C48a, TSO-49b and TSO-C55a
- Power Requirements: 7.5 to 30 Volts, 0.1 amps @ 24V (Typ), 0.2 amps @ 12 Volts (Typ)
- USB Port: For USB Memory Stick use only
- Display: Active Matrix TFT, 262,144 colors, Sunlight readable
- Backlight: External control line, programmable levels
- Display of Primary Gauges with Red and/or Yellow Ranges: Five on the Main Screen + EGT and CHT, One on the Secondary Screen
- Display of Primary and Non-Primary Gauges without Red and/or Yellow Ranges: Five on the Main Screen + EGT and CHT, Six on the Secondary Screen
Electronics International MVP-50 Glass Panel Twin Engine Monitors for 6 cylinder, TSO
$0.00
MVP-50 Display
Weight:1.9 Lbs. Environmental: TSO'd to DO-160 Software: TSOd to DO-178B Power Requirements: 7.5 to 30 Volts, .3 Amps @24V (Typical), .6 Amps @ 12V (Typical). USB Port: For USB Memory Sticks Only (not intended to provide power to other electronic devices) Display: Active TFT Matrix, 262,144 colors. Sunlight readable. Backlight: External Control Line and Internal Electric EyesEDC-33P-4/6
Weight: 1 Lbs. Environmental: Meets TSO (DO-160) Software: Designed and documented to TSO (DO-178B) Power Requirements: 7.5 Volts to 30 Volts, 0.1 amps (Typical).Inputs
Volts: Measured on the power lead of the EDC. Amps: +/- 2.5V differential input, +/- 90V common mode operating range Fuel Flow: 2.5V trigger, 5.11K Ohm pull-up to +5V, 0 to 8.3KHz. RPM: 2 ea. inputs, may be configured for digital or mag input. Selectable jumper for 4 or 6 Cylinder operation. Over voltage protection for RPM: 3V trigger, impendence = 2.06K with 1V pickup. Pressure: 6 ea. inputs, 0 to 2.5V differential input. Impendence >20M Ohms, common mode = 0 to 4 Volts. Temperature: 17 ea. inputs, 0 to 2.5V differential input. Impendence = 12.1K Ohms, common mode = 0 to 4V. Resistive Fuel Level: 4 ea. inputs, 0 to 18V single ended input, impendence = 14.4K Ohms Capacitive Fuel Level: 4 ea. inputs, 0 to 6 KHz. 2.1V trigger, impendence = 33.2K Ohms
Engine Data Monitor 900 System, 9 Cylinder Complete Primary Package, L/R/Aux 4 tank, TSO/STC
$5,892.00
- Dimensions: 4.53 x 3.32, 0.5 deep
- Pre-Wired Harness for all functions
- Display SVGA
- RPM Prop
- MAP Manifold Pressure
- % HP Percent of Horse Power
- EGT Exhaust Gas Temp.
- CHT Cylinder Head Temp.
- EGT Normalize mode
- LOP/ROP JPI Exclusive Leaning Mode
- O-T Oil Temperature
- O-P Oil Pressure
- F-P Fuel Pressure (when in POH)
- OAT Outside Air Temp.
- VDC Voltage (1)
- AMP Current amps (2 twins)
- Fuel Flow Transducer FlowScan
- GPH Gallons per Hour GPH
- REQ Required to wp or destination
- USD Fuel used
- H:M Endurance Hours and Minutes
- MPG Miles per Gal
- CLD Shock Cooling on ALL cylinders
- DIFF Difference between EGT’s
- USB Memory stick 1 GB
- Data Recording 800 Hrs every 6 sec.
- EZTrends Graphing Software free
- 3 year Warranty
Engine Data Monitor 930 System, 9 Cylinder Complete Primary Package, L/R/Aux 4 Tank, TSO/STC, Includes a High Flow Fuel Transducer to 125 GPH
$6,944.00
- Dimensions: 5.97 x 5.11, 2.99 deep
- Pre-Wired Harness for all functions
- Display SVGA
- RPM Prop
- MAP Manifold Pressure
- % HP Percent of Horse Power
- EGT Exhaust Gas Temp.
- CHT Cylinder Head Temp.
- EGT Normalize mode
- LOP/ROP JPI Exclusive Leaning Mode
- O-T Oil Temperature
- O-P Oil Pressure
- F-P Fuel Pressure (when in POH)
- OAT Outside Air Temp.
- VDC Voltage (1)
- AMP Current amps (2 twins)
- Fuel Flow Transducer FlowScan
- GPH Gallons per Hour GPH
- REQ Required to wp or destination
- USD Fuel used
- H:M Endurance Hours and Minutes
- MPG Miles per Gal
- CLD Shock Cooling on ALL cylinders
- DIFF Difference between EGTs
- USB Memory stick 1 GB
- Data Recording 800 Hrs every 6 sec.
- EZTrends Graphing Software free
- 3 year Warranty
- EDM-930 ALL IN ONE Bright VGA Display
- Pre-Wired Harness for all functions
- All EGT/ CHT probes
- Oil Pressure Transducer
- Oil Temperature Sensor
- Fuel Pressure Transducer
- Oat Sensor
- RPM Sensor, One required
- Manifold Pressure Transducer
- 100 amp Shunt (2)(for Amps)
- Volts pick-up V-1 and V-2
- 2 GB memory Download/upload stick
- FloScan Fuel Flow Transducer w/firesleeve
- Demo DVD
- 3 year Warranty
Engine Data Monitor 960 System, 6 Cylinder Complete Primary Package, L/R 2 Tank, TSO/STC
$12,400.00
- Pre-Wired Harness for all functions
- Display SVGA
- RPM Prop
- MAP Manifold Pressure
- % HP Percent of Horse Power
- EGT Exhaust Gas Temp.
- CHT Cylinder Head Temp.
- EGT Normalize mode
- LOP/ROP JPI Exclusive Leaning Mode
- O-T Oil Temperature
- O-P Oil Pressure
- F-P Fuel Pressure (when in POH)
- OAT Outside Air Temp.
- VDC Voltage (1)
- AMP Current amps (2 twins)
- Fuel Flow Transducer FlowScan
- GPH Gallons per Hour GPH
- REQ Required to wp or destination
- USD Fuel used
- H:M Endurance Hours and Minutes
- MPG Miles per Gal
- CLD Shock Cooling on ALL cylinders
- DIFF Difference between EGT’s
- USB Memory stick 1 GB
- Data Recording 800 Hrs every 6 sec.
- EZTrends Graphing Software free
- 3 year Warranty
- EDM-960 ALL IN ONE Bright VGA Display
- Pre-Wired Harness for all functions
- All EGT/ CHT probes
- Oil Pressure Transducer
- Oil Temperature Sensor
- Fuel Pressure Transducer
- Oat Sensor
- RPM Sensor, One required
- Manifold Pressure Transducer
- 100 amp Shunt (2)(for Amps)
- Volts pick-up V-1 and V-2
- 2 GB memory Download/upload stick
- FloScan Fuel Flow Transducer w/firesleeve
- Demo DVD
- 3 year Warranty
Twin Engine Data Monitor 960 System
$11,194.00
- Pre-Wired Harness for all functions
- Display SVGA
- RPM Prop
- MAP Manifold Pressure
- % HP Percent of Horse Power
- EGT Exhaust Gas Temp.
- CHT Cylinder Head Temp.
- EGT Normalize mode
- LOP/ROP JPI Exclusive Leaning Mode
- O-T Oil Temperature
- O-P Oil Pressure
- F-P Fuel Pressure (when in POH)
- OAT Outside Air Temp.
- VDC Voltage (1)
- AMP Current amps (2 twins)
- Fuel Flow Transducer FlowScan
- GPH Gallons per Hour GPH
- REQ Required to wp or destination
- USD Fuel used
- H:M Endurance Hours and Minutes
- MPG Miles per Gal
- CLD Shock Cooling on ALL cylinders
- DIFF Difference between EGT’s
- USB Memory stick 1 GB
- Data Recording 800 Hrs every 6 sec.
- EZTrends Graphing Software free
- 3 year Warranty
- EDM-960 ALL IN ONE Bright VGA Display
- Pre-Wired Harness for all functions
- All EGT/ CHT probes
- Oil Pressure Transducer
- Oil Temperature Sensor
- Fuel Pressure Transducer
- Oat Sensor
- RPM Sensor, One required
- Manifold Pressure Transducer
- 100 amp Shunt (2)(for Amps)
- Volts pick-up V-1 and V-2
- 2 GB memory Download/upload stick
- FloScan Fuel Flow Transducer w/firesleeve
- Demo DVD
- 3 year Warranty